Hooking up a three way dimmer switch

Most dimmer switches are set on a 3-way switch. Connect the ground wire to the ground screw on the dimmer switch. Thes types of switches are common in hallways and staircases.

Turn off the power to the circuit. Now, connect the other two wires to the other side, keeping in mind which one goes on top and which one gets connected to the bottom. Therefore, choose to replace the three-way switch that you will probably use the most to control the lighting.

Dave Donovan is a freelance copywriter living in Atco, N. Installing a three-way dimmer switch on an existing 3-way switch circuit is not only a simple job, but it will add flexibility to your lighting design and improve the overall atmosphere of your living space.

That number will help you determine the perfect size of the switch you need to purchase. Lastly, replace the cover plate with one that properly fits the dimmer molding. One side of the switch should have a single red wire attached to it and the other side should have either two black wires and the ground or a black wire, a white wire with a strip of black electrical tape on it and the ground wire.

They are often found in large rooms as well. Common Problem 5 - Not Checking Both Switches Before you put up your tools and tidy the work area, you need to make sure that the lights work from both light switches. Common Problem 1 - Buying the Wrong Size Switch You should calculate the maximum fixture wattage before you buy your dimmer switch.

Bend the top wire upwards of the box and the bottom wire toward the bottom of the box so you will know where they get connected on the dimmer switch.

Install the new cover plate and turn the circuit back on. The maximum wattage should be clearly marked on the fixture. Gently pull the switch out of the box by pulling on the top and bottom tabs. The ground wire is what prevents stray current from electrocuting your family and possessions.

Make sure that you check the fixture for the wattage and not the light bulb currently installed. Take a moment and look at how the switch is wired. Remove the cover plate from the switch and remove the two screws securing the switch to the wall box.

How to Wire a Three-Way Dimmer Switch

You will need to connect this same wire to the common screw on the new dimmer switch. This is the one that you should replace with the dimmer.

If you try and replace them both, the circuit will not work. You may have to take the bulb out to read it, however. Remove the two black wires or the black and taped white wires and bend them out of the way.

Toggle the circuit breaker back on and try out your new three-way dimmer switch! Do not touch the sides of the switch.

With a few tools and your handy wiring diagram, you can add a custom lighting solution to any room in your house. Find the circuit breaker that is delivering the power to the lighting circuit and toggle it OFF. Once you have located the maximum fixture wattage for each individual lamp, you will need to add them up.

For example, if you have wanted to connect the dimmer switch to four recessed lights with a maximum wattage of 75, you will multiply 75 by 4. The ground wire is often white, green, or bare.3 way switch install. However on each 3-way switch, you have a black screw, this is the special one.

On the power coming in from the panel, you would connect that black wire to the one black screw. And on the other switch, you would connect the black wire coming from the light to that black screw. This is a single pole and a three-way dimmer.

How to Install a 3-Way Lighting Dimmer

So this single pole and three-way can be used in both of those applications. So in this case we're going to use this wire because this is a three-way application.

2 switches and 2 dimmers. if you install a spdt switch and a dimmer on one end, plus a dpdt switch and dimmer on the other end, then you can use the switches to determine which dimmer is "hot". the downsides to this plan include more wiring (which could get expensive).

also, it would mean having separate switches and dimmers on each end. Most dimmers are designed to fit a standard wall box opening, which makes it easy to replace the switch for any incandescent or halogen light with a dimmer. Dimmers come in two basic wiring configurations: standard single-pole dimmers and three-way dimmers.

Whether you are looking to reduce energy costs, increase comfort, or manage light control solutions, Lutron products offer the flexibility you need with the energy savings you want. what is the correct way to hook up a dimmer switch to a wall outlet?I have run a three wire from the socket outllet (bare copper wire is ground, 2 black connected to black three wire and white wire (two)connect to socket's white (right) side.

Download
Hooking up a three way dimmer switch
Rated 5/5 based on 21 review